Pellets: Pellets Extruder Set Technical Parameters

PELLETS EXTRUDER SET TECHNICAL PARAMETERS

(3KG/H) Pellet Ext S3:

Extruder+Controller+Hopper Dryer+Air Compressor

Weight: 5.5kg

Size: H473 x W168 x L128 mm

Screw Size: D27 x L275 mm

Screw Treatment: 38CrMoA1A+Nitriding Treatment

(L/D): 10.2:1

Max. Motor Torque: 0.96N.m

Gear Ratio between Motor and Screw: 1:25

Max. Screw Speed: 40 (r/min)

Installable Equipment: Robot Arm & Frame Type

Heating Zones: 3

Cooling Zones: 2 (Insulation Section & Model Cooling)

Temperature Control: PID

Cooling Method: Water Cooling (Insulation Section)+

Air Cooling (Model Heat Dissipation)

Software: IEMAI 3D EXPERT

Power Servo Motor: STEPCNC

Power Supply: 24V

Servo System: 100W

Total Power: 890W

Extruder Control: Servo Motor+Planetary Reducer

Max. Throughput: 3KG/H

Max. Heating Temperature: 300℃

Applicable Nozzle: 1,2,4,6,8,10 mm

Recommended Layer Thickness: 0.5-5 mm

(6KG/H) Pellet Ext P6:

Extruder+Controller+Hopper Dryer+Air Compressor

Weight: 10kg

Size: H692 x W190 x L132 mm

Screw Size: D34 x L365 mm

Screw Treatment: 38CrMoA1A+Nitriding Treatment

(L/D): 10.7:1

Max. Motor Torque: 1.91N.m

Gear Ratio between Motor and Screw: 1:50

Max. Screw Speed: 60 (r/min)

Installable Equipment: Robot Arm & Frame Type

Heating Zones: 3

Cooling Zones: 2 (Insulation Section & Model Cooling)

Temperature Control: PID

Cooling Method: Water Cooling (Insulation Section)+

Air Cooling (Model Heat Dissipation)

Software: IEMAI 3D EXPERT

Power Servo Motor: STEPCNC

Power Supply: 220V/50HZ

Servo System: 0.6KW

Total Power: 2.1KW

Extruder Control: Servo Motor+Planetary Reducer

Max. Throughput: 6KG/H

Heating Temperature: 0-450 ℃

Applicable Nozzle:1,2,4,6,8,10 mm

Recommended Layer Thickness: 0.5-5 mm

(20KG/H) Pellet Ext L20:

Extruder+Controller+Hopper Dryer+Compressed Air Source Components

Weight: 180kg

Size: H1820 x W733 x L338 mm

Screw Size: D36 x L900 mm

Screw Treatment: 38CrMoA1A+Nitriding Treatment

(L/D): 25:1

Max. Motor Torque: 15N.m

Melt Pump Motor Torque: 5.0N.m

Rolling Shaft Motor Torque: 1.91N.m

Gear Ratio between Motor and Screw: 1:30

Gear Ratio between Motor and Melt Pump: 1:40

Gear Ratio between Motor and Rolling Shaft: 1:2

Max. Screw Speed: 83 (r/min)

Max. Melt Pump Speed: 60 (r/min)

Melt Pump Flow: 20kg/h

Screw Heating Temperature: 0-500 ℃

Melt Pump Heating Temperature: 0-450 ℃

Installable Equipment: Robot Arm & Frame Type

Heating Zones: 4

Cooling Zones: 2 (Insulation Section & Melt Pump Coupling)

Temperature Control: PID

Cooling Method: Water Cooling (Insulation Section)+

Air Cooling (Melt Pump Coupling)

End Part Sensor: Equipped with Melt Pressure Sensor

Auxiliary Feeder Type: Optional Pneumatic Vibration Feeder

 (for materials with high surface viscosity such as TPU/PU)

Software:IEMAI 3D EXPERT

Power Servo Motor: STEPCNC

Power Supply: 220V/50HZ

Screw Servo System: 3.8KW

Melt Pump Servo System: 1.5KW

Rolling Shaft Servo System: 0.6KW

Total Power: 15.5KW

Extruder Control: Servo Motor+Planetary Reducer

Maximum Throughput: 20KG/H

Applicable Nozzle: 4,6,8,10,15,20 mm

Recommended Layer Thickness: 2-10 mm

Controller for Pellet Ext S3 & P6

For Pellet Ext L20, the controller will be dedicated version.

Weight: 12kg

Size: H495 x W280 x L620 mm

Compressed Air Inlet Pressure Requirement: 0.6-0.8 Mpa

Compressed Air Inlet Humidity Requirement: <20% RH

Compressed Air Inlet Flow Requirement: >0.45m³/min

Power Supply: 220V/50HZ

Total Power: 950W

Built-in: Circulating Liquid Cooling System, Feeding Control System,

3 sets of 1000W Heating Temperature Controllers, Servo Driver 600W,

12V100W Fan Controller

Hopper Dryer 25kg for Pellet Ext S3 & P6 & L20

Weight: 40kg

Size: H1530 x W870 x L520 mm

Pellets Drying Capacity: 25KG

Drying Humidity: <20% RH

Drying Temperature: 0-120 ℃

Power Supply: 220V/50HZ

Total Power: 3635W

Efficient and Energy-saving

Thermal Circulation Drying

Equipped with Upper/Lower

Discharging Options

Equipped with a discharge port for ease of granular materials cleaning

Air Compressor for Pellet Ext S3 & P6

Power: 2400W

Generated Flow: 180L/min

Air Tank: 65L

Pressure: 0.7Mpa

Weight: 57KG

Size: H65 x W38 x L97 cm

Speed: 1380R/Min

Compressed Air Source Components for Pellet Ext L20

Screw Type Compressor Parameters

Weight: 115kg

Size: H830 x W700 x L600 mm

Generated Flow:1.1m³/min

Generated Pressure: 0.8Mpa

Power Supply: 380V/50HZ

Total Power: 7.5KW

Permanent Magnet Variable Frequency Motor

Air Tank Parameters

Weight: 110kg

Size: H720 x W750 x L1960 mm

Operating Pressure:0.8Mpa

Capacity:600L

The top is equipped with safety automatic exhaust valve.

Drainage holes at the bottom.

Air Dryer Parameters

Weight: 38kg

Size: H660 x W650 x L425 mm

Operating Pressure: 0.4-1.0 Mpa

Air Treatment: 1.5m³/min

Air Source Pressure: 0.8Mpa

Power Supply: 220V/50HZ

Total Power: 370W

The inlet is equipped with a primary filter.

2 precision filters at the outlet.

Scroll to top